earlylkp.blogg.se - Renesas e1e20 self check program

#RENESAS E1E20 SELF CHECK PROGRAM MANUAL#
#RENESAS E1E20 SELF CHECK PROGRAM PC#

Low voltage OCD Board for RL78/G10 (10-pin/16-pin)

#RENESAS E1E20 SELF CHECK PROGRAM MANUAL#

R0E000010ACB20 User's Manual (Isolator for E1 Emulator) (PDF | English, 日本語)Įnables debugging of an MCU with a power-supply voltage such that the on-chip flash ROM cannot be reprogrammed.This product is used between the emulator and a user's system, and is united by the in-circuit connection with the user's system.

#RENESAS E1E20 SELF CHECK PROGRAM PC#

RTE0T00020KCA00000R User's Manual (20-Pin to 14-Pin Conversion Adapter for the E2 emulator) (PDF | English, 日本語)Įnables debugging in environments where the grounds of the user system and the host PC are not the same. RTE0T00020KCA00000R (Bundled with the E2 Emulator) R0E000010CKZ11 User's Manual (Small Connector Conversion Adapter for E1 Emulator) (PDF | English, 日本語)Ģ0-Pin to 14-Pin Conversion Adapter for the E2 Emulator Small Connector Conversion Adapter for the E1 Emulator RTE0T00020KCAC0000J User's Manual User-system Interface Cable for the E2 Emulator (20-20 pins) (PDF | English, 日本語)Ĭonverts the number and pitch of pins of the connector for connecting the emulator.

RTE0T00020KCAC0000J (Bundled with the E2 Emulator) User-system Interface Cable for the E2 Emulator (20-20 pins) It can also be used for the E2 emulator Lite and PG-FP6. This cable is used to connect the E2 emulator. Supply current: Up to 200mA, Supply voltage: 1.8V to 5.0VĮuropean Standards: EN 55022 Class A, EN 55024 (7614-6002: from 3M Japan, 2514-6002：from 3M Limited)Ĭonnection to the system is via the user system interface cable which comes with the product (signals for connection vary with the type of the target MCU). Since the method of connection and the functions may differ with the device you are using, refer to On-chip Debuggers Performance Property (PDF | English, 日本語).

Reference to and changing memory contents while a program runs.

The supported facilities differ with the integrated development environment you are using. Using this feature, unlike the conventional method of “tracing data with the settings of events and conditions,” users can generate the execution history data such as the PC values and register values simply by inserting the debug instructions to the location where you like to check in the program.his feature is available in all RH850 family MCUs, including the ones do not have internal trace memory when debugging. The function enables users to view the execution history of the programs such as the values of the program counter (PC) and the register values together with the debug instructions of MCUs for RH850 family with the CS+ integrated development environment or the MULTI® integrated development environment (GHS MULTI) from Green Hills Software.

Visualizing the history of CAN communicationsįor example, you can set up the stopping of programs or of the measurement of waveforms by simply using the test lead which comes with the E2 emulator to connect the emulator to an external measuring instrument with the CS+ integrated development environment or the MULTI® integrated development environment (GHS MULTI) from Green Hills Software.

Stopping a program when the reception processing time exceeds the design value.

Measuring the reception processing time in CAN communications with the E2 emulator alone.

This eases verifying the speed of CAN communications in terms of system requirements. The following CAN-related tasks are possible in conjunction with the CS+ integrated development environment or the MULTI® integrated development environment (GHS MULTI) from Green Hills Software.

CAN Communications Time Measurement Solution.Visualizing the relationship between program operations and current.Stopping a program when an excessive current is detected.Measuring current with the E2 emulator alone.These shorten the time taken to tune currents. In conjunction with the QE for Current Consumption, a dedicated tool for measuring current drawn, the E2 emulator is capable of the following items. Support for the input and output of external triggers įor example, you can set up the stopping of programs or of the measurement of waveforms by simply using the test lead which comes with the E2 emulator to connect the emulator to an external measuring instrument with the CS+ integrated development environment or the e² studio integrated development environment.